Antec Nine Hundred Two V3 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítačové skříně Antec Nine Hundred Two V3. Antec Nine Hundred Two V3 Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 15
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
NINE HUNDRED TWO V3
U
SER
S
M
ANUAL
Zobrazit stránku 0
1 2 3 4 5 6 ... 14 15

Shrnutí obsahu

Strany 1 - NINE HUNDRED TWO V3

NINE HUNDRED TWO V3 USER’S MANUAL

Strany 2 - Table of Contents

9 Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6

Strany 3

10 3.5 Rewiring Motherboard Header Connections There may come a time that you need to reconfigure the pin-out of a motherboard header connector. E

Strany 4 - 1.2 Diagram

11 Size: 200 x 30 mm three-speed fan Rated Voltage: 12V DC Operating Voltage: 10.8V ~ 13.2V Speed (RPM) Input Current Air Flow Static Pressure

Strany 5 - Hardware Installation Guide

12 Size: 120 x 25 mm TriCool™ fan Rated Voltage: 12V Operating Voltage: 10.2V - 13.8V Speed (RPM) Input Current Air Flow Static Pressure Acousti

Strany 6

13 the holes in the fan are secured to the mount. 3. Use the long screws provided to secure the fan to the mount. Do not overtighten. 4. Run the p

Strany 7

14 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rot

Strany 8

1 Table of Contents Introduction 1.1 Case Specifications ...

Strany 9

2 Congratulations on your purchase of the Nine Hundred Two V3! The best-selling Antec Nine Hundred offers gamers an unbeatable enclosure, one that

Strany 10

3 1.1 Case Specifications Case Type Mid Tower Color Black Dimensions 19.3” (H) x 8.7” (W) x 18.5” (D) 493 mm (H) x 218 mm (W) x 472 mm (D) Weight 2

Strany 11 - Cooling System

4 Hardware Installation Guide 2.1 Setting Up 1. Place the case upright on a flat, stable surface so that the rear panel (power supply and expansi

Strany 12

5 4. Lift up and remove the motherboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the

Strany 13

6 7. There is a 120 mm fan pre-installed into each cage. Connect the 4-pin connector to the power supply. Note: There is a middle fan bracket p

Strany 14

7 2.8 Internal 2.5” Device Installation At the bottom of your case, there are mounting holes designed to support one 2.5” SSD device. 1. Loca

Strany 15

8 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Gro

Komentáře k této Příručce

Žádné komentáře